Jaguar XF-RS

Multi Stage Correction

When the enquiry came through for a Single Stage machine polish on a 911 the last thing I expected to arrive was a French Racing Blue Jaguar XF-RS. In the short time between arranging the initial inspection and bringing the car to see me the client had sold the Porsche and replaced it for this rather shouty V8 Powerhouse.

During it's initial inspection it was quickly evident the bodywork and exterior in general had been through a lot and it was going to take some serious work to get it up to scratch. A solid pastel blue French Racing Blue is an individual colour rarely found on many other Jaguars. 14 weeks later the car arrived onsite and I was relishing at the opportunity to transform such an iconic car for Jaguar.

The RS received the usual treatment outside a thorough decontamination and deep clean prior to the commencement of any machine work. These stages always reveal the true story behind every car and the true level of the task ahead. Booked for a multi stage correction detail I knew I had my work cut out but I wasn't prepared for some of the discoveries I made with the bodywork and wheels. Once inside the car was raised up and the wheels removed. Once I had the wheels off I was able to see the the terrible state they were in, neither me or the client were expecting me to find the nasty smart repairs on the wheels or the heaps of overspray in the barrels so after short discussions with my Wheel guy and the client all four wheels were sent off for full refurbishment while the car was with me. The discoveries didn't end there, the nearside had seen its fair share of repairs, the worst being the rear quarter which left a lot to be desired for.   After completing the full initial assessment, depth readings and inspection delicate surfaces were taped and the initial cutting stage of machine polishing commenced.

In total I spent nearly three days cutting, being a solid paint French Racing blue was a super super soft paint to work with so patience was key. Go in too heavy and the paint micro marred, go in too light and I'd have been there all year. It was about finding a happy medium but the result of that is extended cutting stages as you can't go in with anything too agressive. The upside to this is that very little refining is required as I took my time with cutting very few defects were inflicted by the initial stage. The cutting stages were followed by a refining and finishing stage in order to ensure the striking blue was finished to the highest possible level adding a deep rich gloss and a very sharp crisp finish. In total I spent five long days cutting and refining the paintwork in order to reach a finish I deemed more than acceptable. Door shuts, boot shuts and the engine bay all received some level of polishing to ensure the highest possible finish throughout the vehicle. With final wipe down complete the first stage of coatings got underway with the base layer of GTechniq CS Light applied and left to cure overnight before returning in the morning to apply the top layer of Gtechniq EXO v3. At this point the wheels returned and the coating of the glass and wheels were complete and the end was finally in sight. I tend to spend in the region of a day completing all the final touches once all the coatings are applied. This allows me to work around the vehicle meticulously dressing the engine bay, polishing exhausts, dressing arches and tyres and chasing the level of perfection I pursue.

On the final day the wheels were returned and coated. The wheels unfortunately had seen an extremely hard life. Upon removal the faces had seen multiple cheap smart repairs and at some point some full refurbishments where they had taken the life out of the wheel. Diamond cut wheels are a challenge when it comes to refurbishment if you don't know what your doing, they are extremely easy to mess up and these wheels are prime examples of wheels that have been poorly refurbished time after time. The result of this was that they were not perfect when they returned. The reason being is because so much had been taken from the face of the wheels during previous refurbishments that my wheel guy had very little alloy left to work with making it extremely difficult to get the perfect finish with clean lines between the contrasting diamond cut and black. The client was kept informed throughout and both myself and my wheel guy did all that we could to ensure he was satisfied with the end result but it goes to show you really don't know what your buying until it's in the hands of a professional.

This detail was a challenge from start to finish. I enjoyed every minute of it and in some areas it was a learning curve but I take positives from that and it only makes me a better detailer. The outcome was stunning and was the result of over 100 hours detailing. This doesn't come cheap but when your looking for the level of finish I achieved with the additional touches of wheels and coatings you would be a fool to pay an amateur.

Thats enough of my waffle and time to let the photos do the talking...

BMW M135i

Enhancement Detail - Total Surface Protection

 The BMW M135i to most probably looks like a standard one series, it's not the most lary looking hot hatch but to the trained eye or any enthusiast it's certainly far from any normal one series. Under the bonnet is a three litre straight six engine with an additional twin scroll turbo which combined packs a punch of 320BHP. Not that normal little on series any more is it?

This particular M135i is owned by a soldier and it is his pride and joy. A little toy for the time he spends at home he wanted his pocket rocket looking its finest and booked it in with me after seeing my recent post about the Estoril Blue BMW 435D Gran Coupe I detailed a few months back. He wanted his to bounce with gloss and be rich in clarity as such booked it in with me to receive and Enhancement Detail along with my Total Surface Protection bolt on for the ultimate protection.

Over a 200 Mile round trip It was an early start, I travelled up to Oxford to Detail this little beauty leaving nice and early to get a good days work in. First up was a good deep clean, pulling cobwebs, dirt, leaves, grease and grime out of the engine bay, door and boot jams and then the arches. Meguiars Super Degreaser was the perfect product for the job breaking down the dirt and grime with ease. I then moved on to decontaminating the wheels. Bit Hamber Korrosol was applied liberally and let to soak. Using a variety of brushes and techniques this was agitated around the wheel to break down brake dust and fall out that had built up in the spokes and crevices of the alloy. The next step was to lay down a thick layer of snow foam, left to dwell and then rinsed. This ensures that the paintwork was free of loose dirt which helps prevent further damage when washing as I won't be dragging the loose dirt around the paint. Out came the trusty buckets and my nice big fluffy wash pad. Now the car had been safely washed it was time to decontaminate the paint. First up Bilt Hamber Korrosol was now applied to the paint and left to dwell then rinsed, then the exterior dried. Why dry it now? For tar remover to work effectively the paint needs to be dry, it does work wet but is 10x more effective when dry and quicker! Tar remover applied, dwelled and rinsed then finally the paint and glass were clayed using a clay mitt. 

Now the car is clean and decontaminated and safely dried its time to tape up and prepare for depth readings and inspection before the polishing stages. I work around the car methodically taking paint depth readings to ensure all panels have safe levels of paintwork on them to ensure the polishing can be performed safely. Readings taken and recorded I began testing on the bonnet trying a variety of pads and polishes to see which achieve the desired result. Taped up, Earphones in and Polisher on I worked around the car performing a single stage machine polish lifting light defects from the paint and restoring depth and clarity to the clear coat. After successfully lifting 90% of the defects from the clear coat leaving the odd RDS (Really Deep Scratch) behind due to it being an enhancement and not full correction. After the polishing stages were completed the paintwork was inspected using another pair of eyes (the mrs) and mine with a Sun Gun Torch which will pretty much find anything you can't.  

Happy with the results it was time to seal that finish in with the first part of my Total Surface Protection. Polish Angel Cosmic always looks stunning on German Paintwork so I decided this would suit best, the paintwork was prepped with Polish Angel Primer which contains compounds that are crucial to the bonding process of Cosmic and ensure it bonds properly to the surface of the paint. Now the paintwork was properly prepared I started applying the coating, once applied it was then layered to ensure optimum levels of protection and ensure durability. While these layers were curing I moved onto the wheels, applying two layers of Gtechniq C5 Alloy Wheel Armour and Gtechniq G1 to the glass. With the exterior coatings complete it was time to move onto the finer details. Firstly giving the exhaust a good polish to remove soot and coking, unfortunately the tips of these exhausts had perished so they were not immaculate but im sure you will agree a vast improvement was achieved. Once cleaned and polished the Tips were sealed with Gtechniq C5 which is also a heat resistant coating so can be used on the exhausts as well as the wheels. Next up is rubber and plastic trims, sealed with Gtechniq C4 and Tyres dressed with the only tyre shine that should be used, Meguiars Endurance Tyre Gel. 

The exterior complete it was time to move inside. Matts removed, hoovered and wet vac'd to remove stains and soiling, especially from the drivers matt. While they were drying I hoovered the interior lifting loose dirt in order to clean and coat all interior surfaces. Using Auto Finesse Leather cleaner and a leather brush I agitated the product to lift several years of embedded dirt from the leather pores. Once the leather was properly cleaned it was protected with Gtechniq L1 along with the Matts protected with Smart Fabric adding hydrophobic properties to the fabric. 

Onto the last part of the Total Surface protection, Sealing the engine bay. Trying out a new product on this M135i, Koch Chemie Nano Plast Care, This product forms a highly durable chemical bond with the surface and restores a satin black finish to the plastic and protects it form further deterioration. I was highly impressed with the product and it'll certainly be used again. 

The owner was blown away with the end result, commenting how he wasn't expecting such high levels of attention to detail, another transformation complete. Next!